25 votes
Vote story as "Fresh"
0 votes
Vote story as "Stale"
USD/CHF recovering from 0.8085
USD/CHF is pressuring up after opening the Asian trade at 0.8085, 40 pips below Friday's close. After very little pullback, the pair began its advance to target highs above 0.8140. This price action comes after USD/CHF fell ...
30 votes
Vote story as "Fresh"
0 votes
Vote story as "Stale"
Bernanke Back Tracks on QE3
The Japanese Yen (JPY) found support under Y79 and some sharp buying spooked shorts into thinking the BOJ was entering the market and day highs were seen in quick succession before falling back and pivoting the Y79 level. Overall the USD/JPY traded ...
38 votes
Vote story as "Fresh"
0 votes
Vote story as "Stale"
EUR/JPY up during Asian trade
The pair was likely to find support at 109.59, Tuesday's low, and resistance at 114.77, Monday's high. Meanwhile, the Euro was up against the US Dollar and the British Pound, with EUR/USD gaining 0.19% to hit 1.4170 and EUR/GBP rising 0.14% to hit ...
32 votes
Vote story as "Fresh"
0 votes
Vote story as "Stale"
GBP/USD up as Chinese data boosts risk appetite
By Forexpros.com Forex Pros pros The pound was higher against the US dollar on Wednesday, as the release of upbeat Chinese economic data soothed markets which have been roiled by fears that the euro zone's debt crisis is deepening. ...
28 votes
Vote story as "Fresh"
0 votes
Vote story as "Stale"
USD/CHF nears all time low after FOMC
... too slow to make satisfactory progress toward reducing the unemployment rate. USD/CHF dropped around 50 pips after the minutes and touched a fresh 2-week low at 0.8280, just 6 pips shy of 0.8274 where the pair set its all time low on Jun 28th. ...
3 votes
Vote story as "Fresh"
0 votes
Vote story as "Stale"
USD/JPY at 5-week low under 80.00
Before deciding to trade foreign exchange you should carefully consider your investment objectives, level of experience and risk appetite. The possibility exists that you could sustain a loss of some or all of your initial investment and therefore you ...
23 votes
Vote story as "Fresh"
0 votes
Vote story as "Stale"
Commodity prices slip but remain high
The New Zealand dollar lifted in value relative to all major trading partners. On a trade-weighted basis the exchange rate lifted 2.2%. The NZD/AUD exchange rate lifted the most, rising 3.0% from May, to hit a six-month high on a monthly average basis.
25 votes
Vote story as "Fresh"
0 votes
Vote story as "Stale"
Currency Majors Technical Perspective
Mostly unchanged since past updates, the GBP/USD continues trading in a limited range around 1.6000 showing no much of a bullish strength: hourly chart shows price contained to the upside by 20 SMA, while indicators remain below their midlines. ...
4 votes
Vote story as "Fresh"
0 votes
Vote story as "Stale"
Sterling's sufferance
Before deciding to trade, please ensure you understand the risks involved and take into account your level of experience. Seek independent advice if necessary. FxPro Financial Services Ltd is authorised and regulated by the CySEC (licence no. ...
39 votes
Vote story as "Fresh"
0 votes
Vote story as "Stale"
USD/JPY update (28th June 2011, 06:00)
... the Fed's preferred reading on inflation, grew 1.2% (annualised). While this figure was marginally higher than consensus, it is by no means fuel for the Fed to consider increasing rates. It was positive to see USD/JPY push up to test 81.00; ...
4 votes
Vote story as "Fresh"
0 votes
Vote story as "Stale"
USD/CAD weekly outlook: June 27- July 1
The US is to publish industry data on house price inflation, a leading indicator of the housing industry's health as well as a report on consumer confidence, a leading indicator of consumer spending. The US is to publish industry data on pending home ...
4 votes
Vote story as "Fresh"
0 votes
Vote story as "Stale"
Sciaky to Feature Commercially Available AM Solution at the International ...
Starting with a 3D model from a CAD program, Sciaky's fully articulated, moving electron beam gun deposits metal, layer by layer, until the part is complete, and ready for finish machining. Depending on the part being manufactured, deposition rates can ...


